We use cookies - Find out more
Telephone: +441502 716993
Part Identifier ?
Racor Spare Seal Kit for Racor 900MA, 1000MA Spin On Filters
Racor Logo

Racor Seal Service Kit for Racor 900 & 1000MA Series

Part No. RAC-RK11-1404

€34.54 You pay €34.54 Incl VAT You pay €28.78 Excl VAT

RRP €38.38 €31.98

Save €3.84 (10.0%) Save €3.20 (10.0%)

IN STOCK

0 reviews
Add to Wishlist
Overview
Brand Racor
Contents T-handle O-ring, Nylon Washer, Rubber Seal, Lid Seal, Bowl Seal, O-ring, Check Ball Kit, Drain Gasket, Feed through/plug O-ring, Water Probe/Plug O-ring, Drain Seal, Drain Body O-ring, Drain O-ring
Suitability Racor Marine Turbine Filters: Racor 900MA, Racor 903MA, Racor 1000MA, Racor 1003MA
Description

RK11-1404 complete seal service kit for the following Racor fuel filters, from the Racor marine turbine series:

  • Racor 900MA
  • Racor 903MA
  • Racor 1000MA
  • Racor 1003MA

This seal kit contains the following spares:

  • RK11004 T-handle O-ring
  • 11003 Nylon Washer
  • Rubber Seal
  • RK11007 Lid Seal
  • RK11007 Bowl Seal
  • 11036 O-ring
  • RK 15010B Check Ball Kit
  • Drain Gasket
  • 43506 Feed through or plug O-ring
  • Water Probe / Plug O-ring
  • Drain Seal
  • Drain Body O-ring
  • Drain O-ring
Installation

Tear down is performed in numerical order shown. Rebuild unit in reverse order, replace old parts with new as applicable.

Completely drain the assembly.

  • 1. Remove T-handle and o-ring.
  • 2. Remove lid and lid gasket. On rebuild, lubricate gasket with diesel fuel or motor oil prior to installation.
  • 3. Remove all four capscrews.
  • 4. Remove bowl ring. Metal bowls do not have bowl ring.
  • 5. Remove bowl and bowl gasket. On rebuild, lubricate gasket with diesel fuel or motor oil prior to installation.
  • 6. Remove centrifuge by turning counter-clockwise. Conical baffle will come off with centrifuge.
  • 7. Remove existing checkball seal. On rebuild, bevel on checkball seal points up into housing and flat side faces checkball.
  • 8. Remove existing checkball.
  • 9. With razor blade cut away existing gasket from drain. On rebuild, lubricate gasket with diesel fuel or motor oil prior to installation. Note: For FG assemblies using drain kits RK 11780 or RK 30488, see steps 12 or 13. Marine assemblies see step 14.
  • 10. Remove heater feedthru or feedthru plug and o-ring. On rebuild, lubricate o-ring with diesel fuel or motor oil prior to installation.
  • 11. Remove water probe or bowl plug and o-ring. On rebuild, lubricate o-ring with diesel fuel or motor oil prior to installation.
  • 12. Remove drain from bowl. Unscrew drain stem from drain body. Remove existing o-rings and drain seal (finger). On rebuild, lubricate drain seal (finger) and o-rings with diesel fuel or motor oil prior to installation. To install drain seal, pull finger up thru drain body using pliers; clip off tip.
  • 13. With razor blade cut away existing gasket from drain. Remove o-ring. On rebuild, lubricate gasket and o-ring with diesel fuel or motor oil prior to installation.
  • 14. Remove drain fitting and heat deflector from bowl. Remove existing o-ring and drain gasket. On rebuild, lubricate o-ring with diesel fuel or motor oil prior to installation.

You may also need

Customer ReviewsAdd a review

No reviews yet...

Add a review

loading
This product has been added to your basket.
Loading   Loading...